Metadata-Version: 2.1
Name: wccontrol
Version: 1.15
Summary: Python module/program to control Watts Clever switch
Home-page: https://github.com/bulletmark/wccontrol
Author: Mark Blakeney
Author-email: mark.blakeney@bullet-systems.net
License: GPLv3
Keywords: RPi
Platform: UNKNOWN
Classifier: Programming Language :: Python :: 3
Requires-Python: >=3.4
Description-Content-Type: text/markdown

## WCCONTROL - Watts Clever Switch Control

This is a Raspberry Pi command line program and Python module to switch
on and off a Watts Clever RF Switch via a cheap 433 MHz transmitter
module. I also have a higher level program
[`wcscheduler`](https://github.com/bulletmark/wcscheduler) which imports
this module and can be used to schedule one or more switches on/off at
specified times and days of week.

The `wccontrol` module implements the protocol which was reverse
engineered in the excellent posts
[here](https://goughlui.com/2016/04/10/reverse-eng-watts-clever-easy-off-sockets-wsmart-box-es-aus1103/)
and
[here](https://goughlui.com/2016/04/13/reverse-eng-pt-2-watts-clever-easy-off-wsmart-box-es-aus1103/).

The latest version of this document and code is available at
https://github.com/bulletmark/wccontrol.

### Watts Clever Switch

You need one or more of these:

![Watts Clever RF Switch](http://i.imgur.com/mILcB6m.jpg)

Often this is purchased in a pack with 2, 3, or 4 such switches, and an
IR (infra-red) receiver box which allows you to operate the remote
switches using a standard TV remote which talks IR to the receiver, then
the receiver talks RF 433 MHz to the switches. E.g the pack is:

![Watts Clever Easy Off Pack](http://i.imgur.com/uqLBL8f.jpg)

The `wccontrol` module allows your Raspberry Pi to talk directly via RF
to the switches. You do not need the IR receiver box at all (i.e. you do
not need the blue box in above image), neither to operate or initially
program the switches. `wccontrol` can be used to fully program
switch group and addresses, and then to operate the switches on and off.

### RF Transmitter

You also need a 433 MHz RF transmitter to connect to your Raspberry Pi.

![RF Transmitter](http://i.imgur.com/UHoh3Px.jpg)

RF modules like the above for Raspberry Pi and similar devices are
purchased for only a few bucks on ebay etc, usually as a transmitter and
receiver pair. To use `wccontrol`, we only need the transmitter which is
the smaller board as shown above.

The transmitter has 3 pins which you directly connect to the RPi header
pins using push-on [female to female jumper
wires](https://www.adafruit.com/product/266) as follows.

Tx pin | Description | Raspberry Pi GPIO header
------ | ----------- | ------------------------
Left   | Data        | GPIO4 (board pin 7)
Middle | VCC         | 5V power (e.g. board pin 4 or 2)
Right  | GND         | Ground  (e.g. board pin 6 or 9 or etc)

You can significantly increase the range of the transmitter by soldering
a 17.3 cm copper wire to the ANT pad in the corner of the PCB. Ideally,
orientate the wire parallel to the switches, i.e. if you plug the RF
switch unit directly into a wall socket then orientate the antenna wire
vertically.

Note that `wccontrol` uses GPIO4 by default to drive the transmitter but
you can easily set it to use any of the other Raspberry Pi GPIO pins by
passing the `pin` argument.

### Installation

Requires Python 3.4 or later. Does not work with Python 2. Ensure that
`python3-pip` and `python3-wheel` packages are installed.

`wccontrol` is [available on PyPI](https://pypi.org/project/wccontrol/)
so install the usual way, e.g:

```bash
pip3 install -U wccontrol
```

Or explicitly from [github](https://github.com/bulletmark/wccontrol):

```bash
git clone https://github.com/bulletmark/wccontrol.git
cd wccontrol
sudo pip3 install .
```

#### Make GPIO Device Accessible

To be able to run this utility/module as your normal user you need to
install a udev rule and assign yourself to the `gpio` group.

As root, create `gpio` group:

    sudo groupadd -f -r gpio

Add your user to that group:

    sudo usermod -aG gpio $USER

Install `gpio.rules` (execute one of the following lines depending if
you installed a local git clone, or from where `pip` installed to):

    sudo cp gpio.rules /etc/udev/rules.d/99-gpio.rules
    sudo cp env/share/wccontrol/gpio.rules /etc/udev/rules.d/99-gpio.rules
    sudo cp /usr/share/wccontrol/gpio.rules /etc/udev/rules.d/99-gpio.rules
    sudo cp /usr/local/share/wccontrol/gpio.rules /etc/udev/rules.d/99-gpio.rules

Reboot your RPi and log back in again.

### Groups and Addresses

Before you can operate a switch on/off you must first program it to
respond to a specific _group_ and _address_.

A _group_ is a number 0 to 1023. An _address_ is a number 0 to 7 within
a group that you allocate to specific switches. Address number 6 is
special as it means "all addresses in same group", i.e. you can switch
all devices together in the same group by using address 6. So there are
actually only 7 unique addresses which you can use per group, 0->5 and
7. Thus there are potentially 1024 x 7 individually addressable devices
you can control.

#### Program Group and Address to Device

E.g. say you want to assign your first switch as address 0 in group 0.

1. Ensure power is applied to the switch.
1. Ensure switch is OFF, i.e. press button to turn LED OFF.
1. Press and hold the switch button until the LED fast flashes, then
   slow flashes, then release.
1. Execute the ON command `wccontrol 0 0 1` to program ON.
1. Execute the OFF command `wccontrol 0 0 0` to program OFF.
1. The LED will go OFF and the switch is now programmed.
1. Test using `wccontrol 0 0 1` to confirm the switch goes ON then 
   `wccontrol 0 0 0` to confirm the switch goes OFF.
1. Repeat the above steps for your other switches using a different group/address.

### Example Commands to Switch On and Off

Switch group 0, device 2 to ON:

    wccontrol 0 2 1

Switch group 0, device 2 to OFF:

    wccontrol 0 2 0

Switch group 0, device 3 to ON:

    wccontrol 0 3 1

Switch group 0, device 3 to OFF:

    wccontrol 0 3 0

Switch both (i.e. all) devices in group 0 to ON:

    wccontrol 0 6 1

Switch both (i.e. all) devices in group 0 to OFF:

    wccontrol 0 6 0

### Command Line Options

```
usage: wccontrol [-h] [-p PIN] [-r RETRIES] [-s BITSHORTGAP] [-l BITLONGGAP]
                 [-m MSGGAP]
                 group address {0,1}

Module/program to set a Watts Clever Smart switch on or off.

positional arguments:
  group                 group, 0 to 1023
  address               switch address to write to, 0 to 7 (6=all in same
                        group)
  {0,1}                 value 0=off, 1=on

optional arguments:
  -h, --help            show this help message and exit
  -p PIN, --pin PIN     RPi BCM GPIO pin to output (default: 4)
  -r RETRIES, --retries RETRIES
                        number of retries to send (default: 20)
  -s BITSHORTGAP, --bitshortgap BITSHORTGAP
                        inter bit short gap in microseconds (default: 406)
  -l BITLONGGAP, --bitlonggap BITLONGGAP
                        inter bit long gap in microseconds (default: 937)
  -m MSGGAP, --msggap MSGGAP
                        inter message gap in milliseconds (default: 20)
```

### Using as a Python Module

```python
import wccontrol
wccontrol.set(0, 2, 1)
```

See the stub code in
[`wccontrol.py`](https://github.com/bulletmark/wccontrol/blob/master/wccontrol.py)
or my [scheduler
application](https://github.com/bulletmark/wcscheduler/blob/master/wcscheduler)
for more complete examples using the python module.

### IFTTT Integration

Another example of how this module can be used is to call it from a tiny
web service application you can run on your Raspberry Pi and which can
receive [IFTTT](https://ifttt.com/discover) web-hook messages from the
internet to turn devices on and off. Usually you would just forward a
port from your home firewall/router to the RPi. The web-hooks can be
triggered by the Google Assistant service. So you can say "Hey Google,
turn the Living Room lights on" and it happens! Quite simple and cheap
to implement given the hardware described here. My [scheduler
application](https://github.com/bulletmark/wcscheduler)
for _wccontrol_ has [IFTTT](https://ifttt.com/discover) integration.

<!-- vim: se ai syn=markdown: -->


