{% extends "remapp/base.html" %}

{% block navhelp %}
        <li>
            <a
                href="https://docs.openrem.org/en/{{ admin.docsversion }}/i_not_patient_indicator.html"
                target="_blank" rel="noopener noreferrer"
                data-toggle="tooltip" title="Not-patient indicators documentation - opens in a new tab">
                Not-patient indicator documentation
            </a>
        </li>
{% endblock %}

{% block confnav %}<li class="dropdown active">{% endblock %}

{% block mainblock %}

{% block modify_pattern %}
{% endblock %}

<div class="row">
  <div class="col-md-offset-3 col-md-6">
    <h4>Guidelines</h4>
    <p>
      The patient name and the ID are matched against the patterns you configure. The patterns make use of wildcards as
      per the following table, and are case insensitive:
    </p>
  </div>
</div>
<div class="row">
  <div class="col-md-offset-4 col-md-4">
    <table class="table table-bordered">
      <tr><th>Pattern</th><th>Meaning</th></tr>
      <tr><td><code>*</code></td><td>matches everything</td></tr>
      <tr><td><code>?</code></td><td>matches any single character</td></tr>
      <tr><td><code>[seq]</code></td><td>matches any character in seq</td></tr>
      <tr><td><code>[!seq]</code></td><td>matches any character not in seq</td></tr>
    </table>
  </div>
</div>
<div class="row">
  <div class="col-md-offset-3 col-md-6">
    <p>
      To match all studies where the patient name begins with <code>physics</code>, the pattern should be set to
      <code>physics*</code>. This would match <code>Physics^RoutIQ</code> but not match <code>Testing^Physics</code>
      because there was no wildcard at the start of the pattern. The patient name in DICOM is normally formatted
      <code>Family name^Given name^Middle name^Prefix^Suffix</code>. Therefore to match any studies where the first name
      is <code>Test</code>, you would set the pattern to be <code>*^test*</code> (although this would also match a
      middle name, prefix or suffix equal to <code>test</code> if they were present!
    </p>
    <p>
      If your test patient name always starts with <code>PHY</code> and then a number, you might use this pattern:
      <code>phy[0-9]*</code>. Here we have used a range for the sequence to match any number, but it will only match one
      character per sequence, so a <code>*</code> is required to match all the characters after the first number. This
      pattern will match <code>Phy12345</code> and <code>PHY6test</code> but not <code>Phyliss</code>.
    </p>
  </div>
</div>
<div class="row">
  <div class="col-md-offset-3 col-md-6">
    <h4>Replicating behaviour of release 0.7.4 and earlier</h4>
    <p>
      OpenREM releases before 0.8 had the not-patient identification patterns hard-coded. From release 0.8.0 the
      patterns are (admin) user configurable, but will start with no patterns in place.
    </p>
{% if admin.admingroup %}
    <p>
      To add the patterns that would maintain the behaviour of previous releases,
      <a href="{% url 'not_patient_indicators_as_074' %}>click here</a>.
    </p>
{% endif %}
{% if not admin.admingroup %}
    <p>
      Log in as an admin in order to add the patterns that would maintain the behaviour of previous releases.
    </p>
{% endif %}
  </div>
</div>


{% endblock %}